Ets-lindgren HI-3550 Magnetic Field Monitor (Archived) Manuel d'utilisateur

HIn3550Magnetic Field MonitorUser's ManualCopyright © 1993 by Holaday Industries, Inc.Manual #600053 10/97 $12.50Archived 4/2/10

HIn3550 Manual Page — 5 3.0 UNPACKING AND ACCEPTANCEIntroductionThis section contains information on the procedure forthe unpacking and acceptance of

Page — 6 HIn3550 ManualArchived 4/2/10

HIn3550 Manual Page — 7 4.0 MAINTENANCEThe following user precautions are intended to ensurethat your HIn3550 maintains reliable operation over itsli

Page — 8 HIn3550 ManualFigure 3Low Battery Display FlashingReplacing BatteriesNOTEAll stored data is lost when the batteriesare removed.The HIn3550

HIn3550 Manual Page — 9 Figure 4Test Display5. Insert them according to the diagrams in the inside ofthe battery compartment. To replace a battery

Page — 10 HIn3550 ManualBattery RecommendationsIt is recommended that alkaline batteries be used with theHI-3550. Always use four identical bat

HIn3550 Manual Page — 11 Periodic/Preventive MaintenanceHoladay Industries recommends an annual calibrationcheck of the HIn3550 Magnetic Field Mo

Page — 12 HIn3550 ManualArchived 4/2/10

HIn3550 Manual Page — 13 Figure 5Integrated Time and Integrated Value Cleared5.0 DESCRIPTION OF HInn3550 OPERATIONIntroductionThis section provides

Page — 14 HIn3550 ManualThe HIn3550 can display integrated magnetic flux levelsof up to 999.99 T-h. Integrated flux levels in excess ofthis value a

Revision RecordManual #600053HIn3550 Magnetic Field MonitorRevision Description Date--- Release 11/93A Added CE Label 10/97Archived 4/2/10

HIn3550 Manual Page — 15 Figure 6Instantaneous Value and Peak Hold Value Cleared5.2 Using the Instantaneous Measurement ())B) ModeSlide the AC-DC

Page — 16 HIn3550 ManualFigure 7Stand-by Modevalue that can be displayed is 3.54 T. These readings arealso displayed for any measured field strengt

HIn3550 Manual Page — 17 Figure 8Ready for Alarm ON/OFF Setting5.5 Alarm FunctionSelecting the Alarm Mode1. Slide the Measurement Mode switch to STBY

Page — 18 HIn3550 ManualFigure 9Instantaneous Measurement Alarm ValueFlashing Ready to SetThe instrument is now ready to be set to the desiredalarm

HIn3550 Manual Page — 19 Figure 10Leading Zeros Suppressedsymbol blinks. Pressing the SET button now togglesthe units of measure between mT-h and

Page — 20 HIn3550 ManualFigure 11Leading Zeros SuppressedReady for Alarm ON/OFF Setting Againzeros of the integrating measurement alarm value willbe

HIn3550 Manual Page — 21 Figure 12Integrating Mode Displaywith Both Alarms Set and ONFigure 13Integrating Mode Displaywith Only Integrating Alarm Set

Page — 22 HIn3550 ManualFigure 14Integrating Mode Displaywith Only Instantaneous Alarm Set and ON)B AL-SET and the alarm indicators are visible.b. I

HIn3550 Manual Page — 23 Figure 15OVER is DisplayedWhen the instantaneous alarm setting overlaps theintegrating alarm setting, the instantaneou

Page — 24 HIn3550 Manualalarm will also be reset automatically.When the alarm is reset, the OVER indicator disappears.Archived 4/2/10

TABLE OF CONTENTS1.0 DESCRIPTION ... 1Introduction ... 12.0 SPECIFICATIONS ... 3

HIn3550 Manual Page — 25 -- NOTES --Archived 4/2/10

Page — 26 HIn3550 Manual-- NOTES --Archived 4/2/10

Stopping the Integrating Mode Alarm ... 23Clearing a Manually Interrupted Alarm ... 23Archived 4/2/10

Limited WarrantyHoladay Industries, Inc. warrants each model HIn3550 MagneticField Monitor to be free from defects in material andworkmanship

HIn3550 Manual Page — 1 1.0 DESCRIPTIONIntroductionThe model HIn3550 is a compact, lightweight personalmagnetic field monitor employing three-axis de

Page — 2 HIn3550 ManualFigure 1HInn3550 MagneticField MonitorArchived 4/2/10

HIn3550 Manual Page — 3 2.0 SPECIFICATIONSTarget magnetic field: DC (static) magnetic fields;ELF(50/60 Hz) AC magneticfieldsMeasuring sensor: InAs Ha

Page — 4 HIn3550 ManualOperating Temperature Range:0 °C to 50 °CDisplay: FE Type White liquid crystalBattery: Size AAA alkaline batteries(4 require